ASTM A743 PDF

Baixe grátis o arquivo ASTM Apdf enviado por DANIEL no curso de Engenharia Mecânica. Sobre: Astm a ASTM A/AM(98), Austenitic, corrosion resistant, solution quenched and aged. 21 Sep Articles. Microstructure and Mechanical Properties of ASTM A CA6NM Steel Welded by.

Author: Kajilabar Merisar
Country: Mozambique
Language: English (Spanish)
Genre: History
Published (Last): 5 December 2008
Pages: 35
PDF File Size: 16.70 Mb
ePub File Size: 12.55 Mb
ISBN: 558-4-40262-806-2
Downloads: 65641
Price: Free* [*Free Regsitration Required]
Uploader: Voodoot

NOTE 2—Proper heat treatment of these alloys adtm usually necessary to enhance corrosion resistance and in some cases to meet mechanical properties. In the case of the AW material, hardness values of the weld metal are considerably higher than those of base metal. Effect of delta ferrite on impact properties of low carbon 13Cr-4Ni martensitic stainless steel. Questions or comments about MatWeb?

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Figure atm illustrates mosaics of the weld joints obtained by using a motorized optical microscope OM. This specification covers iron-chromium and iron-chromium-nickel alloy castings for general corrosion-resistant application.

Or if you don’t have an account with us yet, then click here to register. In addition, as mentioned before, no detectable defect has been found through X-ray analysis.

We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. Login to see your most recently viewed materials here. This transformation, mechanically induced in the plastic zone should absorb additional energy, thus effectively increasing the toughness. Thus, both joints would be approved in accordance to this criterion.

For analysis by optical microscopy, the samples were submitted to usual metallographic preparation procedures involving cutting; grinding, polishing and etching with Vilella reagent that consists aetm 5 g if picric acid, 2. The two joints were X-ray tested and have not presented any detectable defects.

The analysis were focused on four regions of each joint as indicated in Figure 3R rootC centerT top and Z heat affected zone. Work Item s – proposed revisions of this standard. The table 3 shows technical parameters used during the weld of the steel.

Cast Stainless Steel CN7MS, ASTM A

Subscribe to Premium Services Searches: Materials Science and Engineering: According to the manufacturer, the material was produced in an electric arc furnace, refined using an AOD furnace Argon Oxygen Decarburization and cast in sand molds as blocks of xx45 mm dimensions. Despite nearly identical toughness values of the weld metal from AW and PWHT samples, results of fracture analysis have shown distinct features in appearance of the fractures as depicted in Figure 12 and Figure Incrivelmente absorvente do primeiro ao How to cite this article.

TOP Related Articles  CMOS 4027 DATASHEET PDF

Microstructural effects on the fatigue crack growth resistance of a stainless steel CA6NM weld. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Property Data This page displays only the text of a material data sheet. Vickers microhardness values presented at the graphics of Figure 10 have shown that all regions of PWHT welded joint present lower hardness values compared to those of the as-welded joint, likely associated to stress-relief and tempering of martensite during PWHT.

The weld joints were free of defects such as cracks, porosity, slag entrapment, lack of fusion and incomplete penetration.

ABSTRACT CA6NM steel is widely used in the manufacture of hydraulic turbines metallic parts, due to its resistance to corrosion and cavitation damage, combined with good weldability and fatigue properties. It is interesting to observe that results from the weld metal for both conditions are essentially the same, near 27 J, indicating that PWHT does affect significantly this property in spite of lower hardness values presented by the material in this condition.

The samples were used in the form of flat specimens. Characteristics and effects of austenite resulting from tempering of 13Cr-NiMo martensitic steel weld metals.

CF16a | A Stainless Steel | MetalTek

Users requiring more precise data for scientific or engineering calculations can click on astk property value to see the original value as well as raw conversions to equivalent units.

Microhardness Vickers measurements were carried out in a Buehler MicroMet model using an applied load of gf for 30 seconds. In case of conflict between the requirements of this specification and Specification ASpecification A shall prevail. However, welding of this type of steel is complex and to ensure a minimum residual stress after welding it is necessary perform a post welding heat treatment PWHT of the part. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.

TOP Related Articles  THE TRADING BOOK ANNE-MARIE BAIYND PDF

Post weld heat-treatment PWHT of this material is applied to ensure a minimum residual stress of the component and increase the toughness. Both joints presented a martensitic microstructure, however, the heat treatment for residual stress relief precipitated a fine dispersion of austenite.

This result is surprising considering the stress relieved microstructure and presence of retained austenite in the weld metal of the PWHT material.

The steel shall be made by the electric furnace process with or without separate refining such as argon-oxygen decarburization. The mosaics shows a weld joint free of defects such as cracks, porosity, slag entrapment, lack of fusion and incomplete penetration.

Science and Technology of Welding and Joining. The temperature control interpasses were also made with the aid of a pyrometer and contact thermometer.

Cast Grade: CF16a

It is assumed that these coarse particles are iron-alloys from the flux cored welding consumable that were not completely melted. Within the text, the SI units are shown in brackets. Please read our License Agreement regarding materials data and our Privacy Policy. Effect of d-ferrite on impact properties of supermartensitic stainless steel heat affected zones. The microstructure and mechanical properties of the as-welded joint was compared to a joint which suffered a post welding heat treatment PWHT.

Figure 4 illustrates the location of the microhardness measurements, including the base metal, weld metal and heat-affected zone. A43 steel plate used in this work was manufactured by Electro Steel Altona S. The work was divided into three main parts: The grades covered by this specification represent types of alloy castings suitable for broad ranges of application which are intended for a wide variety of corrosion environments.

A number in parentheses indicates the year of last reapproval. Link to Active This link will always route to the current Active adtm of the standard.

In the present work, more Charpy coupons where tested as follow: