ISO 23429 PDF

Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.

Author: Akishura Akinoktilar
Country: Bhutan
Language: English (Spanish)
Genre: Politics
Published (Last): 17 October 2018
Pages: 498
PDF File Size: 20.85 Mb
ePub File Size: 15.84 Mb
ISBN: 449-3-26821-837-7
Downloads: 64372
Price: Free* [*Free Regsitration Required]
Uploader: Zulmaran

Every care has been taken to ensure that the file is suitable for use by ISO member bodies.

Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Symbols and designations of dimensions are defined in ISO This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Julyand conflicting national standards shall be withdrawn at the latest by July NOTE Particular attention is drawn to the note in Table 2 and to Table 3 concerning the limitation on ultimate tensile load.

A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. The work of preparing International Standards is normally carried out through ISO technical committees.

For dated references, only the edition cited applies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy.


МКС EN ISO 23429:2009

Table 3 — Minimum ultimate tensile loads for hexagon socket button head screws of the values specified in ISO Thread Property class 8. In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without fracture, the minimum ultimate tensile loads given in Table 3. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

Hexagon socket button head screw ISO – M12 40 – Intermediate nominal lengths according to ISO are permissible.

Standards New Zealand :: Gauging of hexagon sockets

In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the iao performing the editing. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form iiso by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. This third edition cancels and replaces the second edition ISO Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Jso, e.


Sprawdzian gniazd sześciokątnych PN-EN ISO – Google Books

For undated references, the latest edition of the referenced document including any amendments applies. Requirements for non-electrolytically applied zinc flake coatings are covered in ISO Alternative form of socket permissible For broached sockets which are at the maximum limit of size the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is.

Draft International Standards adopted by the technical 234229 are circulated to the member bodies for voting. Technical Committee Mechanical fasteners Publisher and printing: Acceptability Acceptance procedure is covered in ISO ISO shall not be held responsible for identifying any or all such patent rights.

Product Details

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation 24329 were optimized for printing. They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO The main task of technical committees is to prepare International Standards. Endorsement notice The text of ISO All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying or any other data carriers without prior permission from ON!

Adobe is a trademark of Adobe Systems Incorporated.