Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Kazralkis Gomuro
Country: Fiji
Language: English (Spanish)
Genre: Science
Published (Last): 6 July 2012
Pages: 341
PDF File Size: 11.38 Mb
ePub File Size: 6.5 Mb
ISBN: 938-6-75862-838-2
Downloads: 97110
Price: Free* [*Free Regsitration Required]
Uploader: Yom

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

Packaging and Package Marking 9. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

ICS Number Code The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Material can be manufactured to tensile strength ranges other than those shown in Table 2.

The material shall also conform to the requirements asfm to mechanical properties.

ASTM A493 – 16

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.


ASTM does not give any warranty express or implied or make any representation that awtm contents of this abstract are accurate, complete or up to date. This standard has been approved for use by agencies of the Department of Defense. It is informational only and not an official part of the standard; the full text of the ashm itself must be referred to asttm its use and application. Originally published as A — This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

A number in parentheses indicates the year of last reapproval. Current edition approved Jan.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Link to Active This link will always route to the current Active version of the standard.

Soap is generally used. Resistance to Intergranular Corrosion asrm. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. This abstract is a brief summary of the referenced standard.

The producer should be consulted when material is required to tensile strength ranges other than those specied. A superscript epsilon e indicates an editorial change since the asstm revision or reapproval.

atsm Such requirements may include, but are not limited to the following: Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. NOTE 1—A typical ordering description is as follows: An electroplated copper coating is often used. The SI equivalents are in parentheses and may be approximate. The following coatings may be specied: Last previous edition A — The American Society for Testing and A49 takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.


This specification covers cold-finished wstm hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

The following lubricants may be specied: For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. General Requirements for Delivery 4. The steel shall conform to the required chemical composition requirements.

All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. Historical Version s – view previous versions of standard.